Spares
FLOAT SWITCH
The progressive block is highly précised block working on hydraulic system which is used in line for distribution of grease / oil to the different points of lubrication in the metered quantity. Following models are available in our regular production.
| MODEL | DESCRIPTION |
|---|---|
| M FSH-1 | For motorised lub. unit, for electrically oil level sensing NC contact |
| M FSH-2 | For motorised lub. unit, for electrically oil level sensing NO + NC contact |
| M FSV-1 | For motorised lub. unit, for electrically oil level sensing NO + NC contact |
| M FSV-2 | For motorised lub. unit, for electrically oil level sensing NO + NC contact |
PRESSURE SWITCH
MODEL | DESCRIPTION |
|---|---|
| M PS-830 | Pressure switch used in motorised unit for Sensing pressure |
| M PS-040 | Pressure switch used in motorised unit for Sensing pressure. |
PRESSURE GAUGE
| MODEL | DESCRIPTION |
|---|---|
| M PG | For measure the working pressure of lubrication systems.Range 0 - 25, 0 - 35, 0 - 300 Kg/cm2 . |
RELIEF VALVE
| MODEL | DESCRIPTION |
|---|---|
| MRV-030-A | Used for pressure setting in Lubricating units. |
| M RV-030-B | M RV-030-BUsed for pressure setting in Lubricating units |
METERING CARTRIDGES
These are the oil injectors for injecting metered amount of oil to each lubrication point. This is a unit, fitted with a piston and check valve thus requires recharging time of sixty second between two cycles.
| MODELS | ( For different quantity of discharge of oil ) |
|---|---|
| MLE-MC- D-1 | ( 0.05, 0.10, 0.16cc ) |
| MLE-MC- D- 2 | (0.25, 0.40cc) |
| MLE-MC- D- 3 | ( 1.00, 1.60, 2.00 cc) |
DOSE FEEDER (DUAL LINE BLOCKS)
| MODELS | MLEDF-21 | MLE DF-22 | MLE DF-23 | MLE DF-24 |
|---|---|---|---|---|
| Discharge per cycle | 0.5-5 gm/cc | 0.5-5 gm/cc | 0.5-5 gm/cc | 0.5-5 gm/cc |
| No of outlet | 1 outlet | 2 outlet | 3 outlet | 4 outlet |
| Max working pressure | 275kg/cm2 | 275kg/cm2 | 275kg/cm2 | 275kg/cm2 |
MANIFOLDS
MODELS | LL mm | A mm | M | D mm | Mounting Holes |
|---|---|---|---|---|---|
| FM-1 | 35 | 18 | M8X1 | - | 1 |
| FM-2 | 55 | 18 | M8X1 | - | 1 |
| FM-3 | 75 | 18 | M8X12 | 40 | 2 |
| FM-4 | 95 | 18 | M8X1 | 40 | 2 |
| FM-5 | 115 | 18 | M8X1 | 40 | 2 |
| FM-6 | 135 | 18 | M8X1 | 60 | 2 |
| FM-8 | 175 | 18 | M8X1 | 60 | 2 |
| FM-10 | 215 | 18 | M8X1 | 140 | 2 |
| FM-1A | 40 | 22 | M10X1 | - | 1 |
| FM-2A | 65 | 22 | M10X1 | - | 1 |
| FM-3A | 90 | 22 | M10X1 | 50 | 2 |
| FM-5A | 140 | 22 | M10X1 | 50 | 2 |
HOSES
Hoses are used to connect points where flexibility is a must and also mechanical strength required. These hoses are made of synthetic rubber with textile re- inforcement. These hoses are available with 4mm and 6mm steel end fittings with working pressure of 28 Kg/cm² to 200 Kg/cm². OD of these hoses is 13mm and ID of 6.3 mm. The length of hose pipes can be supplied as per costumer requirement.
THROTTLE VALVE
| MODELS | M -TV - l | M -TV - II | M -TV - lII |
|---|---|---|---|
| Drop/Minute | App. 20 Drops | App. 30 Drops | App. 40 Drops |
| Thread Size | 1/8” BSP | 1/8” NPT or M10 x1 | M8x1 Taper or M10 x1 |
METERING CARTRIDGE
| MLE MC D-1 | Dosage 0.01cc, 0.03 cc, 0.05 cc, 0.10 cc and 0.16 cc per stroke |
|---|---|
| MLE MCD-2 | Dosage 0.25 cc, 0.40 cc per stroke. |
| MLE MCD-3 | Dosage 1.0 cc, 1.60 cc, 2.00 ccPer stroke |
MANIFOLDS
Manifolds are used in the installation / fittings of lubrication systems. The Metering cartridges / Distributors are mounted in the Manifolds
